產品名稱:海綿泡沫回彈儀
海綿泡沫回彈儀型號:HMLQ-500
制造標準:
(GB/T6670-2008 ISO8307 ASTM D3574 ISO8307)軟質泡沫聚合材料落球法回彈性能的測定
適用范圍及功能:
適用于測定軟質聚氨酯泡沫塑料的落球式回彈性能.落球回彈是通過給定直徑和質量的鋼球在規定高度上自由落在泡沫塑料試樣上,計算鋼球回彈的zui大高度與鋼球落下高度比值的百分率既回彈率,以回彈率表示泡沫塑料的回彈性能。
滿足08標準A法和B法試驗方法。
主要是測試塑料泡沫材料及海綿材料的回彈性能。
落球回彈測量精度高采用微處理器進行控制,中文顯示,并可打印試驗數據。
技術參數:
1、鋼球回落高度: 460mm(國標) 500mm(美標)
2、鋼球直徑: ¢16mm
3、落球回彈率精度: <1%
4、被測試樣尺寸: 長*寬*高=100 mm×100 mm×100(50)mm
5、自動計算平均回彈高度
6、自動計算平均回彈率
主要配置:
1、試驗主機一臺
2、智能液晶控制操作系統一臺
3、鋼球釋放機構兩套(手動釋放機構1套、自動釋放機構1套)
4、鋼球捕捉機構一套
5、高度調節機構一組
6、精密光電傳感器一套
7、鋼球2個
8、微型打印機一臺
9、水平校準機構一組
試驗步驟:
將調節后的試樣水平置于回彈儀的測試位置上,通過調節使鋼球底部從固定位置到泡沫塑料表面的落下高度為460mm。
在釋放裝置上固定鋼球,然后使鋼球自由落下。
對每一個試樣做三次回彈,取三次回彈中的zui大值。
每次回彈鋼球應落在試樣表面的同一位置上,并且兩次回彈的時間間隔應控制在20s之內。
如果鋼球在回彈過程中碰到或彈出測量裝置,所得數據無效,需重新補做。
北廣其他檢測海綿儀器:
海綿泡沫壓陷硬度測試儀
海綿泡沫落球回彈測試儀
海綿泡沫疲勞沖擊試驗儀
海綿泡沫壓縮*變形試驗儀
海綿泡沫切割機
海綿泡沫拉伸強度試驗機
Product Name: sponge foam ball resilience meter - (liquid crystal display)
Model: HMLQ-500
One, manufacturing standards:
GB/T6670-2008 (ISO8307 ASTM D3574 ISO8307) soft foam polymeric material falling ball method for the determination of rebound performance
Two. Scope and function:
Application in the determination of soft polyurethane foam falling ball rebound performance. Falling ball rebound is through a ball given diameter and quality in a specified height free fall in the foam specimen, and calculate the ball rebound the maximum height and the ball falling height ratio of the percentage of both spring rate, said resilience foam to rebound rate. Meet 08 Standard A method and B test method. The springback of plastic foam and sponge is mainly tested.. The measuring accuracy of falling ball springback is controlled by the microprocessor, and the Chinese display and can print the test data..
Three, technical parameters:
1, the steel ball drop height: 460mm (GB)
500mm (American Standard)
2, the diameter of the steel ball of 16mm:
3. The accuracy of falling ball rebound rate: <1%
4, the size of the test sample: length * width * high mm mm x 100 =100 x 100 (50) mm
5, automatic calculation of average rebound height
6, automatic calculation of the average rebound rate
Four, the main configuration:
1, test host a
2, inligent LCD control operating system a platform
3, the ball release mechanism two sets (manual release mechanism 1 sets, automatic release mechanism 1 sets)
4, steel ball capture mechanism
5, a group of highly regulated organizations
6, a set of precision photoelectric sensor
7, steel ball 4
8, a micro printer
9. Horizontal calibration mechanism
Five. Test procedure:
The adjusted specimen level is placed in the test position of the rebound meter, and the height of the bottom of the steel ball from the fixed position to the foam surface is 460mm. Fix the steel ball on the release device, and then drop the ball freely.. The maximum of the three rebound is taken for three times of each sample.. Each time the rebound ball should fall at the same position of the specimen surface, and the interval between two rebound should be controlled within the 20s. If the steel ball touches or pops up the measuring device during the rebound process, the data is invalid and needs to be renewed..
All other sponge detection instrument:
Sponge foam indentation hardness tester
Sponge foam rebound tester
Sponge foam fatigue impact tester
Sponge foam compression test gauge
Sponge foam cutter
Sponge foam tensile strength tester