XSG-10型洗衣機水管耐壓爆破試驗機采用觸摸屏操作顯示,界面新穎、試驗設置操作簡單,電器控制采用中國臺灣臺達可編程控制器和模擬量控制模塊,整機自動化程度較高、運行平穩。采用觸摸屏操作顯示,界面新穎、試驗設置操作簡單,電器控制采用中國臺灣臺達可編程控制器和模擬量控制模塊,整機自動化程度較高、運行平穩。配套洗衣機管路卡具或其它卡具可進行對洗衣機或其它用管進行平穩升壓,瞬間沖擊,循環沖擊、瞬間爆破等試驗。本機配有微型打印能夠把打印當前的試驗報告和試驗曲線。在試驗操作過程中儀器自動運行升壓、泄壓動作,自動維持壓力沖擊及壓力穩定。溫度部分采用獨立的溫度控制單元采用成型的溫度控制儀表,對水箱溫度自動控制并可以對溫度進行校準。本機關鍵器件采用進口器件保證了儀器運行的穩定性,
XSG-10型洗衣機水管耐壓爆破試驗機技術參數:
1)、壓力范圍:0~10MPa(任意調節)
2)、壓力顯示精度:0.01MPa
3)、控制精度:上限+2%、下限-1%
4)、壓力從0到設定值耗時:不高于60秒
5)、溫度控制范圍:室溫~95℃
6)、溫度顯示范圍:±1℃
7)、時間顯示范圍:0分~9999.59小時
8)、時間顯示精度:1秒
9)、樣品試驗箱窗口面積:不小于50*1000px
10)、電源:AC380V、60Hz
11)、總功率:3kw
12)、試驗路數:1路
XSG-10型滿足試驗要求:
動態測試
將進水管接入水溫82℃-93℃、壓力為0.9Mpa的液壓系統,預熱3分鐘,然后以10秒鐘的間隔進行沖擊實驗共十次,沖擊后的靜壓力為1.38Mpa。試驗結束,管子應無破損、裂痕等。
耐壓測試:
將進水管接入水溫可控、壓力為2Mpa的液壓系統,在60s內把軟管充壓至2Mpa。并在2Mpa壓力下保持5min. 試驗結束,管子應無破損、裂痕等。
爆破測試:
將進水管接入水溫可控、壓力為3.8Mpa的液壓系統,在60s內把軟管充壓至3.8Mpa。并在3.8Mpa壓力下保持5min. 試驗結束,管子應無破損、裂痕等。
Test pressure blasting machine of XSG-10 type water washing machine adopts touch screenoperations display, novel interface, test set has the advantages of simple operation, electrical control of the use of Taiwan delta programmable controller and analog quantity control module,the high degree of automation, stable operation. Touch screen operation display, novel interface, test set has the advantages of simple operation, electrical control of the use of Taiwandelta programmable controller and analog quantity control module, the high degree of automation, stable operation. Supporting washing machine pipe clips or other fixtures can beinstantly on the washing machine or other pipe smoothly boost, shock, impact, the blasting testcycle. This machine is equipped with a miniature printing can take the test reports the currentprinting and test curve. The instrument automatically step-up operation, pressure relief action intest operation process, automatically maintain pressure shock and pressure stability.Temperature part adopts the independent temperature control unit adopts a temperature control instrument forming of water tank, automatic temperature control and can be used to calibrate the temperature. This machine is the key device to ensure the stability of the instrument adopts imported devices running,
Parameters for technical pressure blasting test of XSG-10 type water washing machine:
1), pressure range: 0 ~ 10MPa (adjusted)
2), pressure display precision: 0.01MPa
3), upper limit, lower limit control accuracy: +2% -1%
4), pressure from 0 to set the value of not more than 60 seconds time:
5), the temperature control range: room temperature to 95 DEG C
6), temperature display range: - 1 DEG C
7), time display range: 0 ~ 9999.59 hours
8), time display precision: 1
9), sample test box window area: not less than 50*1000px
10), power: AC380V, 60Hz
11), the total power: 3kw
12), test number: 1
XSG-10 type water washing machine bursting pressure testing machine can meet the test requirements:
Dynamic test
The water inlet pipe access the water temperature of 82 DEG -93 DEG, the pressure for thehydraulic system of 0.9Mpa, preheat for 3 minutes, and then in 10 second intervals of impact experiment a total of ten times, the static pressure after impact 1.38Mpa. The end of the test,the pipe should be no damage, cracks etc..
The withstand voltage test:
The water inlet pipe is access controlled water temperature and pressure for the hydraulicsystem of 2Mpa, within 60s and the hose is pressurized to 2Mpa. And keep the 5min. test under the pressure of 2Mpa end, the pipe should be no damage, cracks etc..
Blasting test:
The water inlet pipe is access controlled water temperature and pressure for the hydraulicsystem of 3.8Mpa, within 60s and the hose is pressurized to 3.8Mpa. And keep the 5min. testunder the pressure of 3.8Mpa end, the pipe should be no damage, cracks etc..