FS-10798 Series Flow Switch
外部可調型流量開關，適用于水，油和氣體
優勢...
- 流速設置: 液體 - 從0.5GPM 到20.0GPM; 氣體- 見下表
- 接口: 1/2" NPT
- 主要結構材質: 黃銅或不銹鋼
- 設置類型: 可調式
概述 / 設計理念:
這類外部可調型流量開關是下列應用的理想選擇：在冷卻液流量故障時保護機床設備；在潤滑劑較少時保護軸承；或確保適當?shù)目諝饬髁?。FS-10798 系列產品
工作壓力高達1000PSIG, 具有很寬的流量設置范圍，同時具有極低的壓損和的重復性。
采用－普通的平頭螺絲刀，就可很方便到進行現場調節?，F(xiàn)場校準后，為防止擅自改動，可將調節部分用螺絲鎖緊。應用:
- 電子設備: Laser Heads, Welders, Power Supplies, High Speed Spindles, X-Ray Tubes, Semiconductor Equipment
- 齒輪和軸承: Presses, Rotating Equipment, Conveyors, Machine Tools, Robotics
- Processing & Dispensing Equipment: Water Purifications and Filtering, X-Ray Film Processing, Beverage Dispensing, Chemical Additives, Gas Sampling, Distilling
| 性能參數: | ||
| 接液材質 | ||
| 殼體 | Brass or 316 Stainless Steel | |
| 活塞 (黃銅殼體) | Polysulfone for Water | |
| 活塞 (不銹鋼殼體) | 316 Stainless Steel Only | |
| 彈簧 | 316 Stainless Steel | |
| O-Ring | Viton ® | |
| Other Wetted Parts | Epoxy | |
| 壓力范圍 | ||
| 工作壓力 | 1000 PSIG (68.9 bar) | |
| 耐壓 | 2500 PSIG (172.4 bar) | |
| 破裂壓 | 5000 PSIG (344.7 bar) | |
| 工作溫度 | ||
| With Brass or S.S. Piston | -20°F to +300°F (-29°C to +148.9°C) | |
| With Polysulfone Piston | -20°F to +225°F (-29°C to +107.2°C) | |
| 其他參數 | ||
| 重復性 | 1% Maximum Deviation | |
| 設定點精度 | ±10% Maximum | |
| 設定點偏差 | 15% Maximum | |
| 開關* | SPDT, 20 VA | |
| 接口 | 1/2" NPT | |
| 電氣連接 | No. 18 AWG, 24" L., Polymeric Lead Wires | |
*These switches are not intended for use in freezing liquids or steam/high condensation environments. Contact Gems for alternative solutions if these environments exist.
Air/Gas Flow Adjustment Ranges
Water or oil flow units should not be utilized for air/gas applications. The FS-10798 Gas Flow configuration utilizes special dash-pot piston for reliability. The flow adjustment ranges are typical for air service. For other gases, the flow range will vary with the density of the gas. Please consult factory for more information.
For 5 PSIG Line* 1 to 75 SCFM Approx.
For 100 PSIG Line 3 to 160 SCFM Approx.
*Minimum 5 PSI line pressure required.
FS-10798 switches are U.L. Approved for Class I, Division 2, Groups A, B, C, D hazardous locations.
所有評論僅代表網友意見，與本站立場無關。